? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 ad6c211-l/s/tr rev 2.00 (08/28/2012) 001521 page 1 of 9 ad6c211- l 1 form a, current limiting 400v / 25 ? mosfet output solid state relay description the ad6c211-l is a bi-directional, single-pole, single- throw, normally open solid-state relay. it provides a load current of 150ma, a high blocking voltage of 400v, and current limiting circuitry in a compact 6 pin dip package. current limiting circuitry provides a level of protection against increased load currents or transient current spikes by active current reducti on across the device, thereby protecting itself and downstream components. the ad6c211-l comes standard in a miniature 6 pin dip package making it ideal for high-density board applications. schematic diagram agency approvals ul / c-ul: file # e201932 vde: file # 40035191 (en 60747-5-2) applications ? reed relay replacement ? multiplexers ? meter reading systems ? medical equipment ? battery monitoring absolute maximum ratings the values indicated are absolute stress ratings. functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. exposure to absolute maximum ratings may cause permanent damage to the device and may adversely affect reliability. storage temperature ??????????..-55 to +125c operating temperat ure ??????????-40 to +85c continuous input current ????????????..50ma transient input current ???????.?????..500ma reverse input control voltage ????..???????6v input power dissipation ?????????????40mw output power dissipation ???????????..800mw solder temperature ? wave (10sec)??????.?.260c solder temperature ? ir reflow (10sec)?.????..260c ordering information part number description ad6c211-l 6 pin dip, (50/tube) ad6c211-ls 6 pin smd, (50/tube) ad6c211-lstr 6 pin smd, tape and reel (1000/reel) note: suffixes listed above are not included in marking on device for part number identification features ? high isolation voltage (3750v rms ) ? low input control current (3ma typ) ? 150ma maximum continuous load current ? 25 ? maximum on-resistance ? active current limiting protection ? long life / high reliability ? rohs / pb-free / reach compliant 1 2 3 4 5 6 i limit (+) input (-) input do not use -/+ load dc connection -/+ load ad6c211-l
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 2 of 9 ad6c211-l/s/tr rev 2.00 (08/28/2012) 001521 ad6c211- l 1 form a, current limiting 400v / 25 ? mosfet output solid state relay parameter symbol min. typ. max. units test conditions input specifications led forward voltage v f - 1.2 1.5 v i f = 10ma led reverse voltage bv r 6 - - v i r = 10 a turn-on current i f - 3 5 ma i o = 150ma turn-off current i foff - 0.5 - ma - output specifications blocking voltage v b 400 - - v i o =1 ? a continuous load current i o - - 150 ma i f =5ma current limit (ac or dc connection) i limit 180 300 - ma ? i f =5ma on resistance r on - 18 25 ? ? i f =5ma, i o =150ma leakage current i oleak - 0.2 1 ? a i f =0ma, v o =400v output capacitance c out - 25 50 pf i f =0ma, f=1.0mhz offset voltage v offset - - 0.2 mv i f =5ma coupled specifications turn-on time t on - 1.5 5.0 ms ? i f =5ma, i o =150ma turn-off time t off - 0.5 1.0 ms ? i f =0ma, i o =150ma coupled capacitance c coupled - 3 - pf contact transient ratio - 2,000 7,000 0 v/ ? s dv = 50v isolation specifications isolation voltage v iso 3,750 - - v rms rh 50%, t=1min input-output resistance r i-o - 10 12 - ?? v i-o = 500v dc electrical characteristics, t a = 25c (unless otherwise specified)
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 3 of 9 ad6c211-l/s/tr rev 2.00 (08/28/2012) 001521 ad6c211- l 1 form a, current limiting 400v / 25 ? mosfet output solid state relay connection diagrams comments option a: normal ac load configuration on resistance: r typ current limit: i limit option b: separate loads & load voltages on resistance: load 1 ~ (r typ / 2) + 3 ? load 2 r typ / 2 current limit: load 1 i limit load 2 n/a - sum power of loads not to exceed maximum package power dissipation option c: dc load with minimal resistance and no current limit on resistance: r typ / 4 current limit: none ad6c211-l current limiting connection diagrams, t a = 25c (unless otherwise specified)
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 4 of 9 ad6c211-l/s/tr rev 2.00 (08/28/2012) 001521 ad6c211- l 1 form a, current limiting 400v / 25 ? mosfet output solid state relay ad6c211-l performance & characteristics plots, t a = 25c (unless otherwise specified) i f =5ma i o =150ma i f =5ma i o =150ma
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 5 of 9 ad6c211-l/s/tr rev 2.00 (08/28/2012) 001521 ad6c211- l 1 form a, current limiting 400v / 25 ? mosfet output solid state relay process step description parameter a preheat start temperature (oc) 150oc b preheat finish temperature (oc) 180oc c preheat time (s) 90 - 120s d melting temperature (oc) 230oc e time above melting temperature (s) 30s f peak temperature, at terminal (oc) 260oc g dwell time at peak temperature (s) 10s h cool-down (oc/s) <6oc/s ad6c211-l solder temperature profile recommendations (1) infrared reflow: refer to the following figure as an example of an optimal temperature profile for single occurrence infrared reflow. soldering process should not exceed temperature or time limits expressed herein. su rface temperature of device package should not exceed 250oc: a b c d f e g h (2) wave solder: (3) hand solder: maximum temperature: 260oc (at terminal) maximum time: 10s pre-heating: 100 - 150oc (30 - 90s) single occurrence maximum temperature: 350oc (at tip of soldering iron) maximum time: 3s single occurrence figure 1
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 6 of 9 ad6c211-l/s/tr rev 2.00 (08/28/2012) 001521 ad6c211- l 1 form a, current limiting 400v / 25 ? mosfet output solid state relay ad6c211-l package dimensions 6 pin dip package note: all dimensions in inches [?] with millimeters in parenthesis () device weight: 0.45g
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 7 of 9 ad6c211-l/s/tr rev 2.00 (08/28/2012) 001521 ad6c211- l 1 form a, current limiting 400v / 25 ? mosfet output solid state relay ad6c211-l package dimensions 6 pin smd surface mount package (-s) note: all dimensions in inches [?] with millimeters in parenthesis () device weight: 0.45g
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 8 of 9 ad6c211-l/s/tr rev 2.00 (08/28/2012) 001521 ad6c211- l 1 form a, current limiting 400v / 25 ? mosfet output solid state relay 6 pin smd tape & reel (-str) note: all dimensions in millimeters ad6c211-l package dimensions
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 9 of 9 ad6c211-l/s/tr rev 2.00 (08/28/2012) 001521 ad6c211- l 1 form a, current limiting 400v / 25 ? mosfet output solid state relay solid state optronics (sso) makes no warranties or representations with regards to the completeness and accuracy of this docume nt. sso reserves the right to make changes to product description, specifications at any time without further notices. sso shall not assume any liability arising out of the application or use of any product or circui t described herein. neither c ircuit patent licenses nor indemnity are expressed or implied. except as specified in sso?s standard te rms & conditions, sso disclaims liability fo r consequential or other damage, and we mak e no other warranty, expressed or implied, including merchantability and fitness for particular use. disclaimer sso does not authorize use of its devices in life support applicat ions wherein failure or malfunc tion of a device may lead to p ersonal injury or death. users of sso devices in life support applications assume all risks of such use and agree to indemnify sso against any a nd all damages resulting from such use. life s upport devices are defined as devices or syst ems which, (a) are intended for surgical i mplant into the body, or (b) support or sustain life, and (c) whose failure to per form when used properly in accordance with instructions for u se can be reasonably expected to result in significant injury to the user, or (d) a critical component of a life support device or system whose failure can be reasonably expected to cause failure of the life support devic e or system, or to affect its safety or effectiveness. life support policy ad6c211-l package marking ad6c211-l yyww date code pin 1
|
